Setting up the Netgear EX6150 WiFi Range Extender is simple and quick. After plugging it in and connecting to its network, access the setup interface through a web browser using “” Follow the on-screen instructions to link the extender to your existing WiFi network. Once configured, relocate the extender to optimize coverage, eliminating dead zones and providing a seamless WiFi experience throughout your home.

How can I manually setup the Netgear EX6150 extender?

  •  Attach the Netgear EX6150 extender to a power source.
  • Turn on the extender by waiting for its Power LED to illuminate.
  • Make a wireless network connection to “NETGEAR_EXT” using your computer or a mobile device.
  • To open a web browser, type “” into the address box.
  • To finish the setup, choose and connect to your current WiFi network by following the on-screen directions.
  • Place the extender in an area that maximizes WiFi coverage. You now have extended WiFi in the locations you’ve chosen when setup is complete.

How do I connect my WPS to my range extender?

It is simple to connect your range extender to your WPS-enabled device:

  • Make sure your range extender is switched on and placed in a spot that is close to your primary WiFi router.
  • Find and press the WPS button on the range extender. The extension will begin to blink its WPS LED when it is prepared for a connection.
  • Navigate to the WiFi settings on your device and select the WPS option. Press a physical button on your device or choose the WPS option in the WiFi settings to initiate WPS.
  • Give the WPS procedure time to connect your device and the range extender. The WPS indications on your device and the extender should both turn solid, signaling

Note:- If you need any assistance regarding your Netgear EX6150 wifi extender so contact our technician or visit the official website that is setup.

Why can’t I log into my NETGEAR EX6150 extender?

Use these procedures to log in to your Netgear EX6150 WiFi Range Extender:

  • Verify that your laptop or mobile device is linked to the WiFi network that your Netgear EX6150, often known as “NETGEAR_EXT,” is broadcasting.
  • On the device you’re linked to, open a web browser.
  • Type “” into the browser’s address bar, or enter the IP address of the extender (often “”) and hit Enter.
  • Your Netgear extender login information will need to be entered. Use the specific credentials you’ve set, or use the default username and password, which are typically “admin” for both.
  • You may control your extender settings on the Netgear Genie setup dashboard once you’ve entered the right credentials.
  • Always log out of to ensure security.

How do I update my Netgear EX6150 extender firmware?

Link to Extender: Verify that your laptop or mobile device is linked to the WiFi network of the Netgear EX6150 extender.

  • On the device you are linked to, open a web browser.
  • Type “” into the address bar or enter the IP address of the extender (usually “”) and hit Enter.
  • Type in the login information for your Netgear extender. Use the standard username and password (“admin”) if you haven’t configured any specific credentials.
  • After logging in, select the “Firmware Update” or “Settings” area. Search for a “Firmware Update” or “Check for Updates” option.
  • If a new firmware version is available, download and install it by following the on-screen directions. To avoid any problems, make sure not to pause the procedure. subsequently

How do I reset my ex6150?

  • Look for the Netgear EX6150 extender’s reset button. Usually, it’s a tiny, inset button.
  • Press and hold the reset button with a paperclip or other comparable instrument. Hold it for five to ten seconds.
  • Let go of the reset button after holding it for a while. During the restart of the extender, the Power LED can blink.
  • Give the extender time to finish rebooting. It could require one or two minutes.
  • The extender will revert to its original factory default settings after restarting. It might require you to reset it with the default passwords and adjust your WiFi settings as necessary.